FreeBSD Manual Pages
ATA(4) FreeBSD Kernel Interfaces Manual ATA(4) NAME ata -- generic ATA/SATA controller driver SYNOPSIS To compile this driver into the kernel, place the following lines in your kernel configuration file: device scbus device ata options ATA_CAM Alternatively, to load the driver as set of modules at boot time, place some of the following lines in loader.conf(5): ata_load="YES" atacard_load="YES" ataisa_load="YES" atapci_load="YES" ataacard_load="YES" ataacerlabs_load="YES" ataadaptec_load="YES" ataahci_load="YES" ataamd_load="YES" ataati_load="YES" atacenatek_load="YES" atacypress_load="YES" atacyrix_load="YES" atahighpoint_load="YES" ataintel_load="YES" ataite_load="YES" atajmicron_load="YES" atamarvell_load="YES" atamicron_load="YES" atanational_load="YES" atanetcell_load="YES" atanvidia_load="YES" atapromise_load="YES" ataserverworks_load="YES" atasiliconimage_load="YES" atasis_load="YES" atavia_load="YES" The first line is for the common hardware independent code, and is a pre- requisite for the other modules. The next three lines are generic bus- specific drivers. Of the rest, ataahci is the AHCI driver. The others are vendor-specific PCI drivers. The ATA_CAM option should always remain in the kernel configuration, to make the driver work as a CAM(4) subsys- tem module. The following tunables are settable from the loader(8): hw.ahci.force set to nonzero value for forcing drivers to attach to some known AHCI- capable chips even if they are configured for legacy IDE emulation (the default is 1, force the attach). hw.ata.ata_dma_check_80pin set to 0 to disable the 80pin cable check (the default is 1, check the cable). hint.atapci.X.msi set to 1 to allow Message Signalled Interrupts (MSI) to be used by the specified PCI ATA controller, if supported. hint.ata.X.devX.mode limits the initial ATA mode for the specified device on specified the channel. hint.ata.X.mode limits the initial ATA mode for every device on the specified channel. hint.ata.X.pm_level controls SATA interface Power Management for the specified channel, allowing some power savings at the cost of additional command latency. Possible values: 0 Interface Power Management is disabled. This is the default value. 1 The device is allowed to initiate a PM state change; the host is passive. 2 The host initiates a PARTIAL PM state transition every time a port becomes idle. 3 host initiates SLUMBER PM state transition every time port becomes idle. Modes 2 and 3 are only supported for AHCI. DESCRIPTION The ata driver gives the CAM(4) subsystem access to the ATA (IDE) and SATA ports of many generic controllers. Depending on the controller, each PATA (IDE) port or each one or two SATA ports are represented to CAM as a separate bus with one or two targets. Most of the bus-management details are handled by the ATA/SATA-specific transport of CAM. Connected ATA disks are handled by the ATA protocol disk peripheral driver ada(4). ATAPI devices are handled by the SCSI protocol peripheral drivers cd(4), da(4), sa(4), etc. This driver supports ATA, and for the most of controllers, ATAPI devices. Command queuing and SATA port multipliers are not supported. Device hot- plug and SATA interface power management is supported only on some con- trollers. The ata driver can change the transfer mode when the system is up and running. See the negotiate subcommand of camcontrol(8). The ata driver sets the maximum transfer mode supported by the hardware as default. However, the ata driver sometimes warns: ``DMA limited to UDMA33, non-ATA66 cable or device''. This means that the ata driver has detected that the required 80 conductor cable is not present or could not be detected properly, or that one of the devices on the channel only accepts up to UDMA2/ATA33. The hw.ata.ata_dma_check_80pin tunable can be set to 0 to disable this check. HARDWARE The currently supported ATA/SATA controller chips are: Acard: ATP850P, ATP860A, ATP860R, ATP865A, ATP865R. ALI: M5228, M5229, M5281, M5283, M5287, M5288, M5289. AMD: AMD756, AMD766, AMD768, AMD8111, CS5536. ATI: IXP200, IXP300, IXP400, IXP600, IXP700, IXP800. CMD: CMD646, CMD646U2, CMD648, CMD649. Cypress: Cypress 82C693. Cyrix: Cyrix 5530. HighPoint: HPT302, HPT366, HPT368, HPT370, HPT371, HPT372, HPT372N, HPT374. Intel: 6300ESB, 31244, PIIX, PIIX3, PIIX4, ESB2, ICH, ICH0, ICH2, ICH3, ICH4, ICH5, ICH6, ICH7, ICH8, ICH9, ICH10, SCH, PCH. ITE: IT8211F, IT8212F, IT8213F. JMicron: JMB360, JMB361, JMB363, JMB365, JMB366, JMB368. Marvell 88SX5040, 88SX5041, 88SX5080, 88SX5081, 88SX6041, 88SX6042, 88SX6081, 88SE6101, 88SE6102, 88SE6111, 88SE6121, 88SE6141, 88SE6145, 88SX7042. National: SC1100. NetCell: NC3000, NC5000. nVidia: nForce, nForce2, nForce2 MCP, nForce3, nForce3 MCP, nForce3 Pro, nForce4, MCP51, MCP55, MCP61, MCP65, MCP67, MCP73, MCP77, MCP79, MCP89. Promise: PDC20246, PDC20262, PDC20263, PDC20265, PDC20267, PDC20268, PDC20269, PDC20270, PDC20271, PDC20275, PDC20276, PDC20277, PDC20318, PDC20319, PDC20371, PDC20375, PDC20376, PDC20377, PDC20378, PDC20379, PDC20571, PDC20575, PDC20579, PDC20580, PDC20617, PDC20618, PDC20619, PDC20620, PDC20621, PDC20622, PDC40518, PDC40519, PDC40718, PDC40719. ServerWorks: HT1000, ROSB4, CSB5, CSB6, K2, Frodo4, Frodo8. Silicon Image: SiI0680, SiI3112, SiI3114, SiI3124, SiI3132, SiI3512. SiS: SIS180, SIS181, SIS182, SIS5513, SIS530, SIS540, SIS550, SIS620, SIS630, SIS630S, SIS633, SIS635, SIS730, SIS733, SIS735, SIS745, SIS961, SIS962, SIS963, SIS964, SIS965. VIA: VT6410, VT6420, VT6421, VT82C586, VT82C586B, VT82C596, VT82C596B, VT82C686, VT82C686A, VT82C686B, VT8231, VT8233, VT8233A, VT8233C, VT8235, VT8237, VT8237A, VT8237S, VT8251, CX700, VX800, VX855, VX900. Some of above chips are also supported by the more featured ahci(4), mvs(4), and siis(4) drivers. If both drivers are loaded at the same time, those will have precedence. Unknown ATA chipsets are supported in PIO modes, and if the standard bus- master DMA registers are present and contain valid setup, DMA is also enabled, although the max mode is limited to UDMA33, as it is not known what the chipset can do and how to program it. NOTES Please remember that in order to use UDMA4/ATA66 and above modes you must use 80 conductor cables. Please assure that ribbon cables are no longer than 45cm. In case of rounded ATA cables, the length depends on the quality of the cables. SATA cables can be up to 1m long according to the specification. External SATA cables can be 2m long and more, but not all controllers work well on long cables, especially at high speeds. SEE ALSO ada(4), ahci(4), cam(4), camcontrol(8), cd(4), mvs(4), siis(4) HISTORY The ata driver first appeared in FreeBSD 4.0. It was turned into a CAM(4) interface module in FreeBSD 9.0. AUTHORS Alexander Motin <mav@FreeBSD.org>, Soren Schmidt <sos@FreeBSD.org> FreeBSD 11.1 June 18, 2012 FreeBSD 11.1
NAME | SYNOPSIS | DESCRIPTION | HARDWARE | NOTES | SEE ALSO | HISTORY | AUTHORS
Want to link to this manual page? Use this URL:
<https://www.freebsd.org/cgi/man.cgi?query=ata&sektion=4&manpath=FreeBSD+9.1-RELEASE>