FreeBSD Manual Pages
INTRO(4) FreeBSD Kernel Interfaces Manual INTRO(4) NAME intro -- introduction to devices and device drivers DESCRIPTION This section contains information related to devices, device drivers and miscellaneous hardware. The device abstraction Device is a term used mostly for hardware-related stuff that belongs to the system, like disks, printers, or a graphics display with its key- board. There are also so-called pseudo-devices where a device driver emulates the behaviour of a device in software without any particular underlying hardware. A typical example for the latter class is /dev/mem, a loophole where the physical memory can be accessed using the regular file access semantics. The device abstraction generally provides a common set of system calls layered on top of them, which are dispatched to the corresponding device driver by the upper layers of the kernel. The set of system calls avail- able for devices is chosen from open(2), close(2), read(2), write(2), ioctl(2), select(2), and mmap(2). Not all drivers implement all system calls, for example, calling mmap(2) on terminal devices is likely to be not useful at all. Accessing Devices Most of the devices in a UNIX-like operating system are accessed through so-called device nodes, sometimes also called special files. They are usually located under the directory /dev in the file system hierarchy (see also hier(7)). Note that this could lead to an inconsistent state, where either there are device nodes that do not have a configured driver associated with them, or there may be drivers that have successfully probed for their devices, but cannot be accessed since the corresponding device node is still missing. In the first case, any attempt to reference the device through the device node will result in an error, returned by the upper layers of the kernel, usually ENXIO. In the second case, the device node needs to be created before the driver and its device will be usable. Some devices come in two flavors: block and character devices, or to use better terms, buffered and unbuffered (raw) devices. The traditional names are reflected by the letters `b' and `c' as the file type identifi- cation in the output of `ls -l'. Buffered devices are being accessed through the buffer cache of the operating system, and they are solely intended to layer a file system on top of them. They are normally imple- mented for disks and disk-like devices only and, for historical reasons, for tape devices. Raw devices are available for all drivers, including those that also implement a buffered device. For the latter group of devices, the dif- ferentiation is conventionally done by prepending the letter `r' to the path name of the device node, for example /dev/rda0 denotes the raw device for the first SCSI disk, while /dev/da0 is the corresponding device node for the buffered device. Unbuffered devices should be used for all actions that are not related to file system operations, even if the device in question is a disk device. This includes making backups of entire disk partitions, or to raw floppy disks (i.e., those used like tapes). Access restrictions to device nodes are usually subject to the regular file permissions of the device node entry, instead of being enforced directly by the drivers in the kernel. Drivers without device nodes Drivers for network devices do not use device nodes in order to be accessed. Their selection is based on other decisions inside the kernel, and instead of calling open(2), use of a network device is generally introduced by using the system call socket(2). Configuring a driver into the kernel For each kernel, there is a configuration file that is used as a base to select the facilities and drivers for that kernel, and to tune several options. See config(8) for a detailed description of the files involved. The individual manual pages in this section provide a sample line for the configuration file in their synopsis portion. See also the sample config file /sys/i386/conf/LINT (for the i386 architecture). SEE ALSO close(2), ioctl(2), mmap(2), open(2), read(2), select(2), socket(2), write(2), devfs(5), hier(7), config(8) HISTORY This manual page first appeared in FreeBSD 2.1. AUTHORS This man page has been written by Jorg Wunsch with initial input by David E. O'Brien. FreeBSD 11.1 January 20, 1996 FreeBSD 11.1
NAME | DESCRIPTION | SEE ALSO | HISTORY | AUTHORS
Want to link to this manual page? Use this URL:
<https://www.freebsd.org/cgi/man.cgi?query=intro&sektion=4&manpath=FreeBSD+11.0-RELEASE+and+Ports>