FreeBSD Manual Pages
POLLING(4) FreeBSD Kernel Interfaces Manual POLLING(4) NAME polling -- device polling support SYNOPSIS options DEVICE_POLLING options HZ=1000 DESCRIPTION Device polling (polling for brevity) refers to a technique that lets the operating system periodically poll devices, instead of relying on the devices to generate interrupts when they need attention. This might seem inefficient and counterintuitive, but when done properly, polling gives more control to the operating system on when and how to handle devices, with a number of advantages in terms of system responsiveness and perfor- mance. In particular, polling reduces the overhead for context switches which is incurred when servicing interrupts, and gives more control on the sched- uling of the CPU between various tasks (user processes, software inter- rupts, device handling) which ultimately reduces the chances of livelock in the system. Principles of Operation In the normal, interrupt-based mode, devices generate an interrupt when- ever they need attention. This in turn causes a context switch and the execution of an interrupt handler which performs whatever processing is needed by the device. The duration of the interrupt handler is poten- tially unbounded unless the device driver has been programmed with real- time concerns in mind (which is generally not the case for FreeBSD driv- ers). Furthermore, under heavy traffic load, the system might be persis- tently processing interrupts without being able to complete other work, either in the kernel or in userland. Device polling disables interrupts by polling devices at appropriate times, i.e., on clock interrupts, system calls and within the idle loop. This way, the context switch overhead is removed. Furthermore, the oper- ating system can control accurately how much work to spend in handling device events, and thus prevent livelock by reserving some amount of CPU to other tasks. Enabling polling also changes the way software network interrupts are scheduled, so there is never the risk of livelock because packets are not processed to completion. MIB Variables The operation of polling is controlled by the following sysctl(8) MIB variables: kern.polling.enable If set to non-zero, polling is enabled. Default is disabled. kern.polling.user_frac When polling is enabled, and provided that there is some work to do, up to this percent of the CPU cycles is reserved to userland tasks, the remaining fraction being available for polling pro- cessing. Default is 50. kern.polling.burst Maximum number of packets grabbed from each network interface in each timer tick. This number is dynamically adjusted by the ker- nel, according to the programmed user_frac, burst_max, CPU speed, and system load. kern.polling.each_burst The burst above is split into smaller chunks of this number of packets, going round-robin among all interfaces registered for polling. This prevents the case that a large burst from a single interface can saturate the IP interrupt queue (net.inet.ip.intr_queue_maxlen). Default is 5. kern.polling.burst_max Upper bound for kern.polling.burst. Note that when polling is enabled, each interface can receive at most (HZ * burst_max) packets per second unless there are spare CPU cycles available for polling in the idle loop. This number should be tuned to match the expected load (which can be quite high with GigE cards). Default is 150 which is adequate for 100Mbit network and HZ=1000. kern.polling.idle_poll Controls if polling is enabled in the idle loop. There are no reasons (other than power saving or bugs in the scheduler's han- dling of idle priority kernel threads) to disable this. Note that -CURRENT apparently has some problems in this respect now, so default is disabled. kern.polling.poll_in_trap Controls if polling is enabled during hardware traps. Enabling this can be useful to improve the network responsiveness of boxes with 100% CPU usage. Default is disabled. kern.polling.reg_frac Controls how often (every reg_frac / HZ seconds) the status reg- isters of the device are checked for error conditions and the like. Increasing this value reduces the load on the bus, but also delays the error detection. Default is 20. kern.polling.handlers How many active devices have registered for polling. kern.polling.short_ticks kern.polling.lost_polls kern.polling.pending_polls kern.polling.residual_burst kern.polling.phase kern.polling.suspect kern.polling.stalled Debugging variables. SUPPORTED DEVICES Device polling requires explicit modifications to the device drivers. As of this writing, the dc(4), em(4), fwe(4), fwip(4), fxp(4), ixgb(4), nge(4), re(4), rl(4), sf(4), sis(4), ste(4), vge(4), vr(4), and xl(4) devices are supported, with others in the works. The modifications are rather straightforward, consisting in the extraction of the inner part of the interrupt service routine and writing a callback function, *_poll(), which is invoked to probe the device for events and process them. (See the conditionally compiled sections of the devices mentioned above for more details.) As in the worst case the devices are only polled on clock interrupts, in order to reduce the latency in processing packets, it is advisable to increase the frequency of the clock to at least 1000 HZ. HISTORY Device polling first appeared in FreeBSD 4.6 and FreeBSD 5.0. AUTHORS Device polling was written by Luigi Rizzo <luigi@iet.unipi.it>. FreeBSD 11.1 March 26, 2005 FreeBSD 11.1
NAME | SYNOPSIS | DESCRIPTION | SUPPORTED DEVICES | HISTORY | AUTHORS
Want to link to this manual page? Use this URL:
<https://www.freebsd.org/cgi/man.cgi?query=polling&sektion=4&manpath=FreeBSD+5.5-RELEASE>