FreeBSD Manual Pages
UART(4) FreeBSD Kernel Interfaces Manual UART(4) NAME uart -- driver for Universal Asynchronous Receiver/Transmitter (UART) devices SYNOPSIS device uart device puc device uart device scc device uart In /boot/device.hints: hint.uart.0.disabled="1" hint.uart.0.baud="38400" hint.uart.0.port="0x3f8" hint.uart.0.flags="0x10" With flags encoded as: 0x00010 device is potential system console 0x00080 use this port for remote kernel debugging 0x00100 set RX FIFO trigger level to ``low'' (NS8250 only) 0x00200 set RX FIFO trigger level to ``medium low'' (NS8250 only) 0x00400 set RX FIFO trigger level to ``medium high'' (default, NS8250 only) 0x00800 set RX FIFO trigger level to ``high'' (NS8250 only) DESCRIPTION The uart device driver provides support for various classes of UARTs implementing the EIA RS-232C (CCITT V.24) serial communications inter- face. Each such interface is controlled by a separate and independent instance of the uart driver. The primary support for devices that con- tain multiple serial interfaces or that contain other functionality besides one or more serial interfaces is provided by the puc(4), or scc(4) device drivers. However, the serial interfaces of those devices that are managed by the puc(4), or scc(4) driver are each independently controlled by the uart driver. As such, the puc(4), or scc(4) driver provides umbrella functionality for the uart driver and hides the com- plexities that are inherent when elementary components are packaged together. The uart driver has a modular design to allow it to be used on differing hardware and for various purposes. In the following sections the compo- nents are discussed in detail. Options are described in the section that covers the component to which each option applies. CORE COMPONENT At the heart of the uart driver is the core component. It contains the bus attachments and the low-level interrupt handler. HARDWARE DRIVERS The core component and the kernel interfaces talk to the hardware through the hardware interface. This interface serves as an abstraction of the hardware and allows varying UARTs to be used for serial communications. SYSTEM DEVICES System devices are UARTs that have a special purpose by way of hardware design or software setup. For example, Sun UltraSparc machines use UARTs as their keyboard interface. Such an UART cannot be used for general purpose communications. Likewise, when the kernel is configured for a serial console, the corresponding UART will in turn be a system device so that the kernel can output boot messages early on in the boot process. KERNEL INTERFACES The last but not least of the components is the kernel interface. This component ultimately determines how the UART is made visible to the ker- nel in particular and to users in general. The default kernel interface is the TTY interface. This allows the UART to be used for terminals, modems and serial line IP applications. System devices, with the notable exception of serial consoles, generally have specialized kernel inter- faces. HARDWARE The uart driver supports the following classes of UARTs: +o NS8250: standard hardware based on the 8250, 16450, 16550, 16650, 16750 or the 16950 UARTs. +o SCC: serial communications controllers supported by the scc(4) device driver. Pulse Per Second (PPS) Timing Interface The uart driver can capture PPS timing information as defined in RFC 2783. The API, accessed via ioctl(2), is available on the tty device. To use the PPS capture feature with ntpd(8), symlink the tty callout device /dev/cuau? to /dev/pps0. The hw.uart.pps_mode tunable configures the PPS capture mode for all uart devices; it can be set in loader.conf(5). The dev.uart.0.pps_mode sysctl configures the PPS capture mode for a specific uart device; it can be set in loader.conf(5) or sysctl.conf(5). The following capture modes are available: 0x00 Capture disabled. 0x01 Capture pulses on the CTS line. 0x02 Capture pulses on the DCD line. The following values may be ORed with the capture mode to configure cap- ture processing options: 0x10 Invert the pulse (RS-232 logic low = ASSERT, high = CLEAR). 0x20 Attempt to capture narrow pulses. Add the narrow pulse option when the incoming PPS pulse width is small enough to prevent reliable capture in normal mode. In narrow mode the driver uses the hardware's ability to latch a line state change; not all hardware has this capability. The hardware latch provides a reliable indication that a pulse occurred, but prevents distinguishing between the CLEAR and ASSERT edges of the pulse. For each detected pulse, the driver synthesizes both an ASSERT and a CLEAR event, using the same timestamp for each. To prevent spurious events when the hardware is intermittently able to see both edges of a pulse, the driver will not generate a new pair of events within a half second of the prior pair. Both normal and narrow pulse modes work with ntpd(8). Add the invert option when the connection to the uart device uses TTL level signals, or when the PPS source emits inverted pulses. RFC 2783 defines an ASSERT event as a higher-voltage line level, and a CLEAR event as a lower-voltage line level, in the context of the RS-232 protocol. The modem control signals on a TTL-level connection are typically inverted from the RS-232 levels. For example, carrier presence is indi- cated by a high signal on an RS-232 DCD line, and by a low signal on a TTL DCD line. This is due to the use of inverting line driver buffers to convert between TTL and RS-232 line levels in most hardware designs. Generally speaking, a connection to a DB-9 style connector is an RS-232 level signal at up to 12 volts. A connection to header pins or an edge- connector on an embedded board is typically a TTL signal at 3.3 or 5 volts. FILES /dev/ttyu? for callin ports /dev/ttyu?.init /dev/ttyu?.lock corresponding callin initial-state and lock-state devices /dev/cuau? for callout ports /dev/cuau?.init /dev/cuau?.lock corresponding callout initial-state and lock-state devices SEE ALSO puc(4), scc(4) HISTORY The uart device driver first appeared in FreeBSD 5.2. AUTHORS The uart device driver and this manual page were written by Marcel Moolenaar <marcel@xcllnt.net>. FreeBSD 11.1 April 26, 2017 FreeBSD 11.1
NAME | SYNOPSIS | DESCRIPTION | HARDWARE | Pulse Per Second (PPS) Timing Interface | FILES | SEE ALSO | HISTORY | AUTHORS
Want to link to this manual page? Use this URL:
<https://www.freebsd.org/cgi/man.cgi?query=uart&sektion=4&manpath=FreeBSD+11.1-RELEASE+and+Ports>