FreeBSD Manual Pages
WL(4) FreeBSD/i386 Kernel Interfaces Manual WL(4) NAME wl -- T1 speed ISA/radio lan card SYNOPSIS device wl0 at isa? port 0x300 irq 5 DESCRIPTION The wl driver controls a radio lan card system made originally by NCR, then ATT, now Lucent. The system is spread-spectrum radio at around 915 mhz (or 2.4 ghz). With the supplied omni-directional antennae, about 400 feet (indoors, more outdoors) can be covered in circumference. This card can talk to the companion (wlp0) pccard. Speeds vary from 1 megabit to theoretically 2 megabits (roughly T1 in speed). The card has three fundamental hardware units, a so-called PSA or pro- grammable storage area, a radio modem, and a ethernet lan controller. The latter component is the ancient (and not very honorable) Intel 82586 ethernet chip. Fundamentally it appears to the operating system as an ethernet system, and speaks IEEE MAC addresses. The radio modem simply translates ethernet packets to/from radio packets, that are either at 2.4 Ghz or 915 mhz depending on the radio modem. It supports a collision avoidance scheme. The lan controller supports promiscuous mode, broad- cast, and multicasting (although there is a glitch in the latter). "It thinks it is ethernet". How it is used depends on the kind of antennae deployed with it. Point to point applications are possible as are ethernet-like lan use. The vendor ships an omni-directional antennae that works in the vicinity of 400 feet (indoors). Point to point antennae can be purchased that will go miles. SETUP The card can either be initialized with the vendor supplied DOS setup software. Typically minimally an IRQ, port, and Network ID must be sup- plied. Michael Smith's wlconfig(8) utility can now be used to do this work from the UNIX side. The card is "not" plug and play. The network id controls whether one set of cards can hear another. If different, cards will read physical packets, but they will be discarded by the radio modem. CONTROL In addition to the config utility, there are several sysctl switches that can be used to modify runtime parameters. The sysctl(8) variables are as follows: machdep.wl_xmit_delay <useconds> This variable will cause the driver to insert a delay on transmit. 250 is the default. The delay should proba- bly be a bit longer on faster cpus and less on slower cpus. It exists because the 82586 was not designed to work with pentium-speed cpu systems and if overdriven will have copious xmit side errors. machdep.wl_ignore_nwid <0 | 1> This switch defaults to 0; i.e., the nwid is not ignored. It can be set to 1 to cause the nwid to not be used. This may be useful when the device is in promiscuous mode as one can watch for all packets and ignore nwid differences. machdep.wl_xmit_watch <milliseconds> This switch is not currently use- ful. machdep.wl_gather_snr <milliseconds> This switch is not currently use- ful. There is also a signal strength cache in the driver. It may be interro- gated with wlconfig(8). Incoming packets are checked for certain hard- ware radio-modem values including signal strength, silence, and quality, which range fro 0..63, 0..63, and 0..15 respectively. Thus one can read out signal strenth values to see how close/far peer nodes are. The sig- nal strength cache is indexed by sender MAC address. There are two sysctls that change how it filters packets. Both are on by default. machdep.wl_wlcache_mcastonly <0 | 1> By default this switch is on. It forces the cache to filter out unicast packets. Only broadcast or multi- cast packets are accepted. machdep.wl_wlcache_iponly <0 | 1> By default this switch is on. It forces the driver to discard non-IP packets and also stores the IP src address. ARP packets are ignored, as are any other network protocol bar- ring IPv4 packets. CAVEATS The 82586 has numerous defects. It may experience transmit-side errors when modern faster cpus send packets at it faster than it can handle. The driver (and probably the chip) does not support an all multicast mode. As a result, it can be used with applications like mrouted(8), but it must go into promiscuous mode for that to work. The driver is slow to change modes from "normal" to promiscuous mode, presumably due to delays in the configuration code. SEE ALSO sysctl(8), wlconfig(8) http://www.wavelan.com HISTORY The wl driver was written by Anders Klemets (thousands of years ago?) and appears to be based on an even older Intel 82586 driver. The 82586 con- troller was one of the first (if not the first?) integrated lan con- troller on the block. That does not mean it was the best either. Anders ported and or created a driver for the ISA wavelan and PCCARD wavelan system too (wlp). Robert T. Morris, Jr. ported the Mach drivers to BSDI. Jim Binkley ported them to FreeBSD 2.1. Michael Smith ported the wl driver only to 2.2.2. Jim and Michael have been maintaining them. The current state of the driver is NOT ANYONE'S FAULT. Thanks to Bernie Doehner and Robert Buaas for contributions. AUTHORS Too numerous to mention. See above. FreeBSD 11.1 July 7, 1997 FreeBSD 11.1
NAME | SYNOPSIS | DESCRIPTION | SETUP | CONTROL | CAVEATS | SEE ALSO | HISTORY | AUTHORS
Want to link to this manual page? Use this URL:
<https://www.freebsd.org/cgi/man.cgi?query=wl&sektion=4&manpath=FreeBSD+4.5-RELEASE>